Посыпалась рыба 7200.7

# smartctl -i /dev/sda
smartctl 5.39.1 2010-01-28 r3054 [i686-pc-linux-gnu] (openSUSE RPM)
Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net
 
=== START OF INFORMATION SECTION ===
Model Family:     Seagate Barracuda 7200.7 and 7200.7 Plus family
Device Model:     ST380013AS
Serial Number:    3JV2KYD9
Firmware Version: 3.05
User Capacity:    80 026 361 856 bytes
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   6
ATA Standard is:  ATA/ATAPI-6 T13 1410D revision 2
Local Time is:    Sun Aug  8 03:51:03 2010 MSD
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
 

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
 
General SMART Values:
Offline data collection status:  (0x82) Offline data collection activity
                                        was completed without error.
                                        Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                 ( 430) seconds.
Offline data collection
capabilities:                    (0x5b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        No Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        No General Purpose Logging support.
Short self-test routine
recommended polling time:        (   1) minutes.
Extended self-test routine
recommended polling time:        (  58) minutes.
 
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   053   048   006    Pre-fail  Always       -       12736514
  3 Spin_Up_Time            0x0003   098   097   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   100   100   020    Old_age   Always       -       52
  5 Reallocated_Sector_Ct   0x0033   100   100   036    Pre-fail  Always       -       21
  7 Seek_Error_Rate         0x000f   085   060   030    Pre-fail  Always       -       377197952
  9 Power_On_Hours          0x0032   092   092   000    Old_age   Always       -       7511
 10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   099   099   020    Old_age   Always       -       1431
194 Temperature_Celsius     0x0022   044   051   000    Old_age   Always       -       44
195 Hardware_ECC_Recovered  0x001a   053   047   000    Old_age   Always       -       12736514
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   199   000    Old_age   Always       -       1
200 Multi_Zone_Error_Rate   0x0000   100   253   000    Old_age   Offline      -       0
202 Data_Address_Mark_Errs  0x0032   100   253   000    Old_age   Always       -       0
 
SMART Error Log Version: 1
ATA Error Count: 51 (device log contains only the most recent five errors)
        CR = Command Register [HEX]
        FR = Features Register [HEX]
        SC = Sector Count Register [HEX]
        SN = Sector Number Register [HEX]
        CL = Cylinder Low Register [HEX]
        CH = Cylinder High Register [HEX]
        DH = Device/Head Register [HEX]
        DC = Device Command Register [HEX]
        ER = Error register [HEX]
        ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after

rror 51 occurred at disk power-on lifetime: 7423 hours (309 days + 7 hours)
  When the command that caused the error occurred, the device was active or idle.
 
  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 2f 18 92 25 e0  Error: UNC at LBA = 0x00259218 = 2462232
 
  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  42 00 ff 48 91 25 e0 00      00:08:30.949  READ VERIFY SECTOR(S) EXT
  42 00 ff 49 90 25 e0 00      00:08:30.997  READ VERIFY SECTOR(S) EXT
  42 00 ff 4a 8f 25 e0 00      00:08:30.993  READ VERIFY SECTOR(S) EXT
  42 00 ff 4b 8e 25 e0 00      00:08:30.991  READ VERIFY SECTOR(S) EXT
  42 00 ff 4c 8d 25 e0 00      00:08:30.988  READ VERIFY SECTOR(S) EXT
 
Error 50 occurred at disk power-on lifetime: 7423 hours (309 days + 7 hours)
  When the command that caused the error occurred, the device was active or idle.
 
  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 e4 7a 5f 41 e0  Error: UNC at LBA = 0x00415f7a = 4284282
 
  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  42 00 ff 5f 5f 41 e0 00      00:04:58.271  READ VERIFY SECTOR(S) EXT
  42 00 ff 60 5e 41 e0 00      00:04:58.267  READ VERIFY SECTOR(S) EXT
  42 00 ff 61 5d 41 e0 00      00:04:58.263  READ VERIFY SECTOR(S) EXT
  42 00 ff 62 5c 41 e0 00      00:04:58.259  READ VERIFY SECTOR(S) EXT
  42 00 ff 63 5b 41 e0 00      00:04:58.255  READ VERIFY SECTOR(S) EXT
 
Error 49 occurred at disk power-on lifetime: 7423 hours (309 days + 7 hours)
  When the command that caused the error occurred, the device was active or idle.
 
  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 ca 98 8c 10 e0  Error: UNC at LBA = 0x00108c98 = 1084568
 
  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  42 00 ff 63 8c 10 e0 00      00:04:10.113  READ VERIFY SECTOR(S) EXT
  42 00 ff 64 8b 10 e0 00      00:04:10.109  READ VERIFY SECTOR(S) EXT
  42 00 ff 65 8a 10 e0 00      00:04:10.105  READ VERIFY SECTOR(S) EXT
  42 00 ff 66 89 10 e0 00      00:04:10.101  READ VERIFY SECTOR(S) EXT
  42 00 ff 67 88 10 e0 00      00:04:10.097  READ VERIFY SECTOR(S) EXT
 
Error 48 occurred at disk power-on lifetime: 7423 hours (309 days + 7 hours)
  When the command that caused the error occurred, the device was active or idle.
 
  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 da 0a 1b 00 e0  Error: UNC at LBA = 0x00001b0a = 6922
 
  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  42 00 ff e5 1a 00 e0 00      00:03:51.194  READ VERIFY SECTOR(S) EXT
  42 00 ff e6 19 00 e0 00      00:03:51.190  READ VERIFY SECTOR(S) EXT
  42 00 ff e7 18 00 e0 00      00:03:51.319  READ VERIFY SECTOR(S) EXT
  42 00 ff e8 17 00 e0 00      00:03:51.316  READ VERIFY SECTOR(S) EXT
  42 00 ff e9 16 00 e0 00      00:03:51.313  READ VERIFY SECTOR(S) EXT
 
Error 47 occurred at disk power-on lifetime: 7417 hours (309 days + 1 hours)
  When the command that caused the error occurred, the device was active or idle.
 
  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 2f 18 92 25 e0  Error: UNC at LBA = 0x00259218 = 2462232
 
  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powere